1204 User Guide

	Go to this device's product page

Getting Started

Checking the Contents

You should have received: A PhidgetTextLCD Adapter A mini-USB cable Mounting hardware kit		In order to test your new Phidget you will also need: An LCD An LCD cable

Connecting the Pieces

Connect your LCD to the Adapter using your LCD cable. The connector can be difficult to push in on both ends- If it isn't going in, try pushing a little bit harder. Connect the PhidgetTextLCD Adapter to your computer using the Mini-USB cable.

Testing Using Windows 2000 / XP / Vista / 7

Make sure you have the current version of the Phidget library installed on your PC. If you don't, follow these steps:

1. Go to the Quick Downloads section on the Windows page
2. Download and run the Phidget21 Installer (32-bit, or 64-bit, depending on your system)
3. You should see the icon on the right hand corner of the Task Bar.

Running Phidgets Sample Program

Double clicking on the icon loads the Phidget Control Panel; we will use this program to ensure that your new Phidget works properly.

The source code for the TextLCD-full sample program can be found in the quick downloads section on the C# Language Page. If you'd like to see examples in other languages, you can visit our Languages page.

Updating Device Firmware

If an entry in this list is red, it means the firmware for that device is out of date. Double click on the entry to be given the option of updating the firmware. If you choose not to update the firmware, you can still run the example for that device after refusing.

Double Click on the icon to activate the Phidget Control Panel and make sure that the PhidgetTextLCD Adapter is properly attached to your PC.
LCD Display Tab Double Click on PhidgetTextLCD Adapter in the Phidget Control Panel to bring up TextLCD-full and check that the box labelled Attached contains the word True. Choose the screen. Select the screen size. Click on Initialize to set-up and clear the display. Click on the Backlight box. The screen will light up. Click on the Cursor box. A “dash” cursor will appear on the screen. Click on the Cursor Blink box. A square blinking cursor will appear on the screen. You can increase or decrease the LCD contrast by moving the pointer in the Contrast slider box. You can increase or decrease the LED Brightness by moving the pointer in the Brightness slider box. You can type your message to be displayed on the LCD screen. To make your own characters, click on the Custom Characters Tab.
Custom Characters Tab Draw your custom character. Select the memory location (you can store up to 8 characters in location 0 to 7). Select the screen. Store the custom character in the memory location. The stored values are shown in the boxes. The algorithm is described in the Technical Section of the manual. You can see your custom character by typing \0 (in the case of Memory Location 0) in one of the text boxes on the “LCD Display” tab.

Testing Using Mac OS X

1. Go to the Quick Downloads section on the Mac OS X page
2. Download and run the Phidget OS X Installer
3. Click on System Preferences >> Phidgets (under Other) to activate the Preference Pane
4. Make sure that the is properly attached.
5. Double Click on in the Phidget Preference Pane to bring up the Sample program. This program will function in a similar way as the Windows version.

Using Linux

For a step-by-step guide on getting Phidgets running on Linux, check the Linux page.

Technical Details

Introduction

Liquid Crystal Displays are display devices used to convey information through arrangements of pixels. Graphic and Text LCDs are the most common types available for electronic products. The 1204 supports the following screen sizes (lines x characters): 1x8, 2x8, 1x16, 2x16, 4x16, 2x20, 4x20, 2x24, 1x40, 2x40, 4x40. Please note that your program has no way of automatically detecting the size of the attached screen, so you need to set the screen size with call from the API in order to have text strings display properly.

Connector

Below is a pinout diagram for the connector on the 1204, with descriptions of each pin. Remember to use the end of the cable with the larger connector with the 1204 if you want the wire colors to be consistent with the diagram.

• A: LED Anode (+)
• K: LED Cathode (-)
• VSS: Board Ground
• VDD: Supply Voltage (5V)
• VO: LCD Operating Voltage
• RS: Register Selector
• R/W: Read/Write Signal
• DB0-DB7: Data Bus Lines

Text LCDs

Text LCDs display full text strings set in software. Since text characters are defined from the ASCII standard library, other ASCII standard set characters and glyphs can also be sent to the text LCD. This can be done easily by using unicode characters within your text string. In C#, this may look something like this:

tLCD.rows[0].DisplayString = "Apple starts with \u0041";

In this example, the string \u indicates that a unicode character follows, and the unicode character 0041 (which references the hexadecimal character code 0x41) represents the capital letter A. After the LCD converts the unicode character, the above example would cause the LCD screen to read Apple starts with A. A chart of all ASCII standard set character codes is available here.

Custom Characters

Custom characters can also be generated for the PhidgetTextLCD. A custom character can be any arrangement of pixels within the space allotted for a single character. Single characters are made up of pixels arranged in a grid 5 pixels wide by 8 pixels high. Once generated, custom characters can be stored in any one of eight volatile memory locations on the PhidgetTextLCD, and can be recalled with a simple API command from software. When custom characters are designed, a formula is used to change the pixel design into a pair of numerical values. The first value relates to the design of the top 4 rows of the character, and the second value relates to the design of the bottom 4 rows of the character. Unlike the unicode characters used in the Special Characters section above, the calculated number is not in hexadecimal format but is an integer value up to six characters in length. The calculation for custom characters can be done by hand, or can be completed for you by using the form available at www.phidgets.com/documentation/customchar.html. Done by hand, each integer value represents the sum of two to the power of each individual on-pixel’s location within that integer-value’s half of the character. Pixels not turned on are valued at zero. For example, a custom character happy-face with pixels 6, 8, 11 and 13 in the upper half turned on, pixels 1, 3, 6, 8, 11, 12 and 13 in the lower half turned on, and all other pixels turned off, would result in the following integer values.

These two values are then stored in one of eight memory locations (CG-RAM 0 to 7) on the PhidgetTextLCD by using the Set Custom Character method in software. In C#, this may look something like this:

tLCD.customCharacters[0].setCustomCharacter(10560, 14666)

Once stored, characters can be recalled into a text string by either using the unicode value for the location as referenced in the ASCII chart (Appendix A) or by using the String Code method from the API. Examples in C# of both methods are shown below:

tLCD.rows[0].DisplayString = "I am happy \u0008";

tLCD.rows[0].DisplayString = "I am happy " + tLCD.customCharacters[0].StringCode;

API

Enums

enum {

PHIDGET_TEXTLCD_SCREEN_NONE,

PHIDGET_TEXTLCD_SCREEN_1x8,

PHIDGET_TEXTLCD_SCREEN_2x8,

PHIDGET_TEXTLCD_SCREEN_1x16,

PHIDGET_TEXTLCD_SCREEN_2x16,

PHIDGET_TEXTLCD_SCREEN_4x16,

PHIDGET_TEXTLCD_SCREEN_2x20,

PHIDGET_TEXTLCD_SCREEN_4x20,

PHIDGET_TEXTLCD_SCREEN_2x24,

PHIDGET_TEXTLCD_SCREEN_1x40,

PHIDGET_TEXTLCD_SCREEN_2x40,

PHIDGET_TEXTLCD_SCREEN_4x40,

} ScreenSizes This is a list of the supported screen sizes. The 4x40 screen is a special case because it requires both of the enable lines - so when it is attached, it must be setup on screen 0, and screen 1 cannot be used.