1135 User Guide

Getting Started

Checking the Contents

You should have received: A Precision Voltage sensor A sensor cable		In order to test your new Phidget you will also need: A PhidgetInterfaceKit 8/8/8 A USB cable A 9V battery

Connecting the Pieces

Connect the Precision Voltage Sensor to an Analog Input on the PhidgetInterfaceKit 8/8/8 board using the sensor cable. Connect the voltage source to the terminal block. It is possible to connect the leads of the voltage source to either terminal - the reported voltage may just be of the opposite polarity. Connect the InterfaceKit board to your PC using the USB cable.

Testing Using Windows 2000 / XP / Vista / 7

Make sure you have the current version of the Phidget library installed on your PC. If you don't, follow these steps:

1. Go to the Quick Downloads section on the Windows page
2. Download and run the Phidget21 Installer (32-bit, or 64-bit, depending on your system)
3. You should see the icon on the right hand corner of the Task Bar.

Running Phidgets Sample Program

Double clicking on the icon loads the Phidget Control Panel; we will use this program to ensure that your new Phidget works properly.

The source code for the InterfaceKit-full sample program can be found in the quick downloads section on the C# Language Page. If you'd like to see examples in other languages, you can visit our Languages page.

Updating Device Firmware

If an entry in this list is red, it means the firmware for that device is out of date. Double click on the entry to be given the option of updating the firmware. If you choose not to update the firmware, you can still run the example for that device after refusing.

Double Click on Phidget InterfaceKit 8/8/8 in the Phidget Control Panel to bring up InterfaceKit-full and check that the box labelled Attached contains the word True. Make sure that the Ratiometric box is not Ticked. With no connections on the input terminal blocks, the Analog In value should be approximately 500. The value displayed shows the 9V battery actual voltage when the battery’s + wire is connected to the VIN+ terminal block. You can adjust the input sensitivity by moving the slider pointer. Click on the Sensors button to bring up the Advanced Sensor Form.
In the Advanced Sensor Form, select the 1135 - Voltage Sensor from the drop down menu. The differential voltage measured by the sensor is shown here. Formula used to convert the analog input SensorValue into voltage.

Testing Using Mac OS X

1. Go to the Quick Downloads section on the Mac OS X page
2. Download and run the Phidget OS X Installer
3. Click on System Preferences >> Phidgets (under Other) to activate the Preference Pane
4. Make sure that the is properly attached.
5. Double Click on in the Phidget Preference Pane to bring up the Sample program. This program will function in a similar way as the Windows version.

Using Linux

For a step-by-step guide on getting Phidgets running on Linux, check the Linux page.

Technical Details

General

The Voltage Sensor measures the differential voltage between the input terminals and outputs the difference proportionally. The maximum differential voltage that can be measured accurately is +/-30V. When the positive and negative inputs are equal, the analog output value is 2.5V. When the positive input is 30V greater than the negative input, the analog output is 4.5V and when the positive input is 30V less than the negative input, the analog output is 0.5V.

Since the 1135 Voltage Sensor can measure a differential voltage, the common mode rejection (CMR) is an important specification. CMR refers to the amount of voltage that both input terminals of an differential amplifier can be offset without affecting the output gain. For example, if the positive terminal sees a voltage of 7V and the negative terminal sees a voltage of 5V, then the CMR would be 5V and would output a value of 2V at unity gain. For the 1135 Voltage Sensor, it is able to measure the differential voltage of +/-10V with a CMR of 40V while keeping the accuracy within 2%. Please note that the error specifications do not include the error introduced by the Analog to Digital Conversion on the Analog Input. (if you are using the 1135 with a PhidgetInterfaceKit) The majority of error introduced by the Analog to Digital conversion is from the error in the voltage reference (0.5% max), and the limitation of resolution in the SensorValue property. The best accuracy can be achieved by using a 2 or more point calibration of your system - effectively calibrating the 1135 and the PhidgetInterfaceKit in a single step. If you are calibrating, be sure to use a good quality multimeter to determine the voltage being applied.

Using RawSensorValue in the formula will increase the resolution, which is limited by SensorValue to about 67mV.

Formulas

The Formula to translate SensorValue into differential voltage is:

$V_diff=frac{frac{SensorValue}{200}-2.5}{0.0681}$

where V_diff is defined as V_positive - V_negative.

Coding for your Sensor

Phidget analog sensors do not have their own API, but instead their output is a voltage that is typically converted to a digital value and accessed through the SensorValue properties and events on a Phidget InterfaceKit. It is not possible to programmatically identify which sensor is attached to the Analog Input. Your application will need to apply the formula from this manual to the SensorValue to translate it into usable data. Please see the Phidget InterfaceKit product manual for code samples, an overview of its API, and a description of our architecture.

Analog Input Cable Connectors

Each Analog Input uses a 3-pin, 0.100 inch pitch locking connector. Pictured here is a plug with the connections labeled. The connectors are commonly available - refer to the Analog Input Primer for manufacturer part numbers.