Solid State Relay Guide

Introduction

Solid state relays (SSRs) are devices that can be used to turn on or turn off the power being supplied to other devices without the need of a physical switch. With relays, it is possible to control high-current devices with low-current signals, like a standard DC signal from a Digital Output. This can help cut down on the amount of heavy-duty wiring and controllers needed for your project.

Functionally, they are the same as Mechanical Relays, but have the following advantages:

• SSRs produce less electromagnetic interference during operation, as opposed to mechanical relays whose internal contacts tend to spark when switching.
• While the switch contacts of a mechanical relay will eventually wear down from sparking, an SSR will have a longer life because its internals are purely digital.
• SSRs exhibit faster response times than mechanical relays (≈1ms compared to ≈10ms).
• SSRs are less susceptible to electric shock and physical vibrations than mechanical relays.
• Since the switch inside an SSR isn't a mechanical switch, it does not suffer from contact bounce, and operates silently.

Of course, since SSRs are more complex, they are more expensive to produce and will dissipate more energy in the form of heat (1-2% of the energy intended to power the load).

How it Works

The two inputs are connected internally to an optocoupler. An optocoupler is a circuit component that uses an LED and a light sensitive element to link two parts of a circuit without directly connecting them electrically. The light sensor is connected to the transistors which open and close the path that supplies the relay's load with power.

Basic Use

• talk about basic (and not-so-basic?) uses of relays (switching, dimming?, motor control?)
• talk about switching high power (>20W)
• talk about high-frequency switching (and other max specs)
• list other challenges and solutuons

• Safety related stuff:

Since relays can switch high currents and voltages, they can be potentially quite hazardous. Make sure you never touch the terminals while the relay is powered, and use the plastic cover if the relay came with one.

Also ensure the terminal screws are tightened properly, as loose screws could cause excess heat to be generated.

Types of Solid State Relays

The main defining characteristic that separates Solid State Relays (SSRs) is the type of current they can switch. If you want to read about Mechanical Relays instead, you can visit the

Alternating Current (AC)

• show diagram of AC SSR
• mention zero-cross / random

Direct Current (DC)

• show diagram of DC SSR
• mention zero-cross / random (only use random)

Versatile (AC/DC)

• show diagram of AC/DC SSR
• mention zero-cross / random

Choosing an SSR

There many factors to consider when choosing an SSR, and you need to know what kind your application needs before deciding on one.

Current Type

Some SSRs are designed to switch AC current, some switch DC current, and others can switch both.

Large "Hockey Puck" type SSRs are usually built for large loads and are often AC or DC specific.

Small, versatile ones that can switch either current are designed for lower current and voltage.

Make sure you check your SSR's data sheet to ensure that it can switch the type of current your load is using.

Application Load

Be sure to choose an SSR that can handle the current and voltage requirements of the load you're switching. This is often more complicated than making sure the rated currents and voltages match, since some devices can have quick surges of current on startup. As a general rule, make sure the SSR can handle the maximum surge value of your application, not just the usual operating current.

• Talk about transformers

• talk about lamps

• talk about heaters

Heat Sinks

Check your SSR's data sheet to get an idea of the amount of heat it will be generating based on your application's load. If the SSR cannot be mounted on a surface that is suitable for conducting away the heat, you should use a heatsink.

Noise Protection

Some AC relays will typically have built-in noise protection in the form of a "snubber". A snubber is a simple RC circuit that will absorb small transients and will protect against unintentional turn-on.

For large transients and highly inductive loads, additional protection is necessary. A simple way to do this is to add a Metal Oxide Varistor (MOV) across the load terminals.

Conclusion

• reiterate introduction, quickly review important features and differences of various SSRs

How to Buy

• table of SSRs categorized with product links