Language - iOS

application are built using the Cocoa Touch framework and the Objective C programming language, both developed by Apple.

Introduction

If this is your first time working with a Phidget, we suggest starting with the Getting Started page for your specific device. This can be found in the user guide for your device. That page will walk you through installing drivers and libraries for your operating system, and will then bring you back here to use iOS specifically.

iOS is capable of using nearly the complete Phidget API, including events. As iOS do not have USB ports, Phidgets can only be remotely controlled over a network, by using the Phidget Webservice. We also provide example code in iOS for the Phidget InterfaceKit, Hello World examples and a Skeleton starter project.

iOS can be developed with Xcode on OS X..

You can compare iOS with our other supported languages.

Quick Downloads

Just need the iOS documentation, drivers, libraries, and examples? Here they are:

Documentation

• C API

Example Code

• Example Code (same file as iOS libraries)

Libraries and Drivers

• iOS Libraries (same file as iOS examples)
• OS X Drivers Installer

Getting Started with Cocoa Touch

If you are new to writing code for Phidgets, we recommend starting by running, then modifying existing examples. This will allow you to:

• Make sure your libraries are properly linked
• Go from source code to a test application as quickly as possible
• Ensure your Phidget is hooked up properly

As iOS development is primarily done on Xcode, we provide instructions for Xcode, specifically version 4.0.

Use Our Examples

Start by ensuring that the Webservice is running on the computer that the Phidget is connected to. This computer needs to have an USB port and can be an OS X system as well as any other operating systems we support. For directions on how to set up and run the Webservice on a remote computer, refer to the page for that operating system

Then on the the OS X system that will be used for developing iOS applications, download and unpack the Phidget Examples for iOS. The easiest way to confirm that your environment is set up properly will be to compile and run the HelloWorld iOS example. Start by opening the HelloWorld.xcodeproj in Xcode.

Next, select your target destination that you want the application be ran on: an iOS device or simulator.

To run the example, click on the Run button.

This program will detect for devices that are attached/detached on the host computer. Go ahead, and attach or detach your devices! Here is an example output:

After confirming that the HelloWorld example is working, you can proceed to run the example for your device. If you aren't sure what the software example for your device is called, check the software object listed in the Getting Started Guide for your Device. Currently, the only device we provide example code for is the PhidgetInterfaceKit.

Once you have the iOS examples running, we have a teaching section below to help you follow them.

Write Your Own Code

When you are building a project from scratch, or adding Phidget function calls to an existing project, you'll need to configure your development environment to properly link the Phidget iOS library. To begin:

1. Generate a new iOS Windows-based application project with a descriptive name such as PhidgetTest.

A .xcodeproj project file will be created.

2. Set up the Provisioning Profiles and Code Signing settings, if necessary.

3. Download the Phidget iOS library and extract it.

4. Inside, you will find the iphoneos and the iphonesimulator folders. Move the two folders as well as the phidget21.h into the same directory as the the newly created .xcodeproj file.

5. In xCode, open up the Project Settings → Build Settings.

6. In Linking → Other Linker Flags, follow these steps for both the Debug, and Release sections:

Select Any iOS Simulator SDK and enter: $(SRCROOT)/iphonesimulator/libPhidget21.a.

Select Any iOS SDK and enter: $(SRCROOT)/iphoneos/libPhidget21.a.

7. In Search Paths → Header Search Paths, enter: $(SRCROOT).

8. In the header file, add a reference to phidget21.h:

#import "phidget21.h"

The project now has access to Phidgets and we are ready to begin coding.

Please note that the iPhone library also contains a sample skeleton xCode project for iOS. This project already contains project settings similar to those discussed above and it lets you quickly start on Phidgets development.

The same teaching section which describes the examples also has further resources for programming your Phidget.

Follow the Examples

By following the instructions above, you probably now have a working example and want to understand it better so you can change it to do what you want. This section has resources for you to learn from the examples and write your own.

Your main reference for writing iOS applications will be our C API information, with syntax for all of our functions:

• C API (This is the complete set of functions you have available for all Phidgets)
• Device Specific APIs - The one for your Phidget can be found in its user guide.

To learn the details behind opening, configuring, using, and closing your Phidget, try the General Phidget Programming page. That page also describes using the Phidget in an event-driven manner and in a traditional manner, both of which are available in iOS.

API Support

Most of the C API is supported in iOS, with the exception of the local open calls. This is because there are no USB ports on iOS devices, so only the remote open calls can be used.

The following open calls are unsupported:

int CPhidget_open(CPhidgetHandle phid, int serialNumber)
int CPhidget_openLabel(CPhidgetHandle phid, const char * label)

Code Snippets

Specific calls in iOS will differ in syntax from those on the General Phidget Programming page, but the concepts stay the same.

It may help to have the General Phidget Programming page and this section open at the same time, because they parallel each other and you can refer to the Android Java syntax. However, many additional concepts are covered on the General Phidget Programming page on a high level, such as using multiple Phidgets, handling errors, and different styles of programming.

For example, if we were using a Phidget Interface Kit as our device, the general calls would look like this:

Step One: Initialize and Open

For opening a remote Phidget over the network using the Webservice:

  CPhidgetInterfaceKitHandle device;
 
  // Open first detected Interface Kit, remotely with IP address and port
  CPhidget_openRemoteIP((CPhidgetHandle)device, -1, "192.168.3.33", 5001, NULL);

Since the Webservice is used to connect to the Phidget, the one connection per device limit does not apply.

The open calls will tell the program to continuously try to connect to a Phidget, based on the parameters given, even trying to reconnect if it gets disconnected. This means that simply calling open does not guarantee you can use the Phidget immediately. We can handle this by using event driven programming and tracking the attach events and detach events.

Step Two: Wait for Attachment (plugging in) of the Phidget

To use the Phidget, it must be plugged in (attached). We can handle this simply by calling CPhidget_waitForAttachment. This function works for any Phidget. CPhidget_waitForAttachment will block indefinitely until a connection is made to the Phidget, or an optional timeout is exceeded:

int serialNum;
CPhidget_waitForAttachment(10000);
CPhidget_getSerialNumber((CPhidgetHandle)device, &serialNum);
NSLog("%d attached!", serialNum)

Sometimes, it makes more sense to handle the attachment via an event. This would be in instances where the Phidget is being plugged and unplugged, and you want to handle these incidents. Or, when you want to use event-driven programming because you have a GUI-driven program. In these cases, an event-driven code snippet to handle the attachment might look something like this.

First, you hook an event handler with the following code:

- (BOOL)application:(UIApplication *)application didFinishLaunchingWithOptions:(NSDictionary *)launchOptions
   ...   
   CPhidgetManager_set_OnAttach_Handler(manager, gotAttach, self);
   ...
}

Next, the callback method needs to be set up:

// ========== Event Handling Setup Functions ==========
int gotAttach(CPhidgetHandle phid, void *context) {
    NSAutoreleasePool *pool = [[NSAutoreleasePool alloc] init];
    
    //invokes the DeviceAttach event method on the main thread and block the main thread until after the DeviceAttach method finishes
	//A bad access exception may occur if you set waitUntilDone to No
	[(id)context performSelectorOnMainThread:@selector(DeviceAttach:)
								  withObject:[NSValue valueWithPointer:phid]
                               waitUntilDone:YES];
    [pool release];
    return 0;
}

Above, the DeviceAttach method is invoked on the main thread. The NSAutoreleasePool object is created to clean up released objects on the event thread, and is released at the end of the method. The DeviceAttach method is defined as follows:

// ========== Event Handling Functions ==========
- (void)DeviceAttach:(NSValue *)phid
{
    int phidgetSerial;
    const char * phidgetName;
    
    CPhidget_getSerialNumber((CPhidgetHandle)[phid pointerValue], &phidgetSerial);
    CPhidget_getDeviceName((CPhidgetHandle)[phid pointerValue], &phidgetName);
    
    outputField.text = [NSString stringWithFormat:@"%@Hello Device %@, Serial Number: %d\n\n", outputField.text, [NSString stringWithCString:phidgetName encoding:NSASCIIStringEncoding], phidgetSerial];
}

With this function, the code inside DeviceAttach will get executed every time the PhidgetInterfaceKit is attaches to the computer. Some events such as Attach and Detach belong to the base Phidget object and thus are common to all types of Phidgets. Please refer to the API manual and the iOS examples for a list of events and their usage.

Step Three: Do Things with the Phidget

You can read data and interact with your Phidget both by polling it for its current state (or to set a state), or by catching events that trigger when the data changes.

For our PhidgetInterfaceKit, the polling method of getting the current sensor state and setting an output state looks something like this:

# Get a data point from Analog Port 0
int sensorValue;
CPhidgetInterfaceKit_getSensorValue(device, 0, &sensorValue);
[sensorValueTxt setintValue: sensorValue];

# Set digital output port 0 to be on
CPhidgetInterfaceKit_setOutputState(device, 0, 1);

Step Four: Close and Delete

At the end of your program, don’t forget to call CPhidget_close() and CPhidget_delete() to free any locks on the Phidget that the CPhidget_open() call put in place!

CPhidget_close((CPhidgetHandle)ifkit);
CPhidget_delete((CPhidgetHandle)ifkit);

The complete set of functions you have available for all Phidgets can be found in the C API. You can also find more description on any device-specific function either in the Device API page for calls available only on your specific Phidget.